Insulated Terminals 产品系列
Phoenix 绝缘端子由 T2 铜制成,带有镀锡的端子筒和 PVC 绝缘层,其硬度持久不变,不会开裂也不会回弹。该系列覆盖 0.5–6 mm² (22–10 AWG) 线径,使用红色、蓝色、黑色和黄色颜色编码,符合美国、日本和德国标准。
Ring Insulated Terminals
RV SeriesRV Series ring insulated terminals have a copper terminal body with a colour-coded PVC sleeve that stays hard, does not crack and does not rebound. The closed ring encircles the stud completely, so the joint cannot pull free under vibration.
查看系列
Fork Insulated Terminals
SV SeriesSV Series fork insulated terminals use the same copper body and colour-coded PVC sleeve as the ring series, with an open fork mouth that slides under a loosened screw — no need to remove the fastener during assembly or service.
查看系列
Blade Insulated Terminals
DBV SeriesDBV Series blade insulated terminals have a copper body with a colour-coded PVC sleeve. The flat tab fits standard 2.8 mm, 4.8 mm and 6.3 mm quick-disconnect receptacles, so the connection can be pulled apart without tools. Suitable for 22–10 AWG copper wire and rated for 600 V.
查看系列
Pin Insulated Terminals
PTV SeriesPTV Series pin insulated terminals end-mount stranded copper wire with a solid round pin that plugs directly into relay sockets, PCB connectors and spring-cage blocks. The PVC sleeve is colour-coded to wire cross-section. Suitable for 22–10 AWG and rated for 600 V.
查看系列
Male Disconnect Terminals
MDD SeriesMDD Series male disconnect terminals feature a flat copper tab inside a colour-coded PVC or nylon shroud. The tab plugs into a matching female receptacle for a secure yet separable connection. Used in automotive harnesses, appliance wiring and control panels.
查看系列
Female Disconnect Terminals
FDD SeriesFDD Series female disconnect terminals accept a matching male blade into a copper contact housed in a colour-coded PVC or nylon sleeve. The sleeve prevents accidental contact with live metal. Suitable for the same wire and voltage range as the MDD male series.
查看系列
Fully Insulated Terminals
FDD Full Insulated TypeFDFD Series fully insulated disconnect terminals encase the entire contact in nylon so there is no exposed metal on either the male or female half. This double-insulated design is mandatory in high-density wiring where accidental bridging between adjacent connectors must be prevented.
查看系列
Male & Female Hook Insulated Terminals
PBDD SeriesPBDD Series hook terminals have the same copper body as the blade disconnect family but with a 90° bend in the tab so that the mating connector faces sideways. This right-angle exit is chosen where wire must route parallel to the panel surface without a sharp reverse bend.
查看系列
Male Bullet Terminals
MPD SeriesMPD Series male bullet terminals have a round copper pin inside a colour-coded PVC sleeve. The 4 mm bullet pin mates with a matching female receptacle to form a push-on connection widely used in automotive lighting, motorcycle wiring and low-voltage equipment.
查看系列
Female Bullet Terminals
FRD SeriesFRD Series female bullet terminals accept the 4 mm male bullet pin inside a copper socket housed in a colour-coded PVC sleeve. The spring contact grips the pin firmly enough to resist vibration while still allowing manual disconnection. Standard in automotive, marine and motorcycle harnesses.
查看系列
Flag Terminals
FLDNY SeriesFLDNY Series flag terminals exit the wire at 90° to the tab, so the crimped wire runs parallel to the mounting surface rather than doubling back. This reduces bend stress on the conductor and saves space in crowded panel wiring. Colour-coded nylon or PVC sleeve for 22–10 AWG.
查看系列系列对比
所有 15 个绝缘系列并排对比 — 比较端子形状、线径范围、连接尺寸和绝缘材料。
| 系列 | 端子形状 | 线径范围 | 柱 / 片 / 针尺寸 | 绝缘 |
|---|---|---|---|---|
|
|
Ring | 0.5–6 mm² (22–10 AWG) | #4–1/2" stud (3.2–12.5 mm) | PVC |
|
|
Fork | 0.5–6 mm² (22–10 AWG) | #4–5/16" stud (3.2–8.2 mm) | PVC |
|
|
Blade | 0.5–6 mm² (22–10 AWG) | 2.3–4.5 mm blade width | PVC |
|
|
Pin | 0.5–6 mm² (22–10 AWG) | 10 / 13 / 18 mm pin length | PVC |
|
|
Male disconnect | 0.5–6 mm² (22–10 AWG) | 2.8 / 4.75 / 6.35 mm tab (110 / 187 / 250) | PVC |
|
|
Female disconnect | 0.5–6 mm² (22–10 AWG) | 2.8 / 4.75 / 6.35 mm tab (110 / 187 / 250) | PVC |
|
|
Female disconnect | 0.5–6 mm² (22–10 AWG) | 2.8 / 4.75 / 6.35 mm tab, fully covered barrel | PVC |
|
|
Hook | 0.5–6 mm² (22–10 AWG) | 6.35 mm hook (250) | PVC |
|
|
Male bullet | 0.5–6 mm² (22–10 AWG) | 4.0–5.0 mm bullet (156 / 195) | PVC |
|
|
Female bullet | 0.5–6 mm² (22–10 AWG) | 3.9–4.9 mm bullet (156 / 195) | PVC, fully insulated |
|
|
Flag | 0.5–6 mm² (22–10 AWG) | 6.35 mm flag (250) | Nylon |
|
|
Male spring | 0.5–6 mm² (22–10 AWG) | 4.0–5.0 mm bullet (156 / 195) | Nylon |
|
|
Female spring | 0.5–6 mm² (22–10 AWG) | 3.9–4.9 mm bullet (156 / 195) | Nylon |
|
|
Ring | 0.5–6 mm² (22–10 AWG) | #4–1/2" stud (3.2–12.5 mm) | Heat shrink |
|
|
Fork | 0.5–6 mm² (22–10 AWG) | #4–5/16" stud (3.2–8.2 mm) | Heat shrink |
绝缘端子选择指南
按照以下简单步骤选择合适的绝缘端子。
-
1
识别连接类型
环形、叉形、刀片、针等。
-
2
匹配线径
例如 22–16 AWG, 16–14 AWG
-
3
确认连接尺寸
螺柱尺寸、刀片宽度、针脚直径等
-
4
选择绝缘类型
PVC、热缩、或全绝缘
行业与应用
适用于汽车、家电、机械和电力设备制造的绝缘端子。
-
工业控制与自动化
面板制造商使用环形和叉形端子进行PLC I/O接线、接触器和端子块,需要安全的螺丝连接。
-
汽车与运输
线束制造商指定彩色绝缘端子用于照明、传感器和电源电路,其中抗振动性能很重要。
-
家用电器
洗衣机、空调器和烤箱依靠全绝缘端子进行内部布线,这些布线必须保持安全且紧凑。
-
工业机械
机器制造商将环形、叉形和断开端子安装到电机、传感器和在苛刻环境中运行的控制柜。
-
电气设备制造
开关设备和配电板使用镀锡铜端子进行稳定的电流传输并抵抗腐蚀。
常见问题解答
绝缘端子是做什么用的?
绝缘端子将绞铜线连接到电气设备的螺丝、螺柱和插片上。PVC套筒覆盖压紧枪管,使接头保持绝缘并免受振动和潮湿。典型应用包括控制面板、汽车线束、家用电器和工业机械。
有哪些类型的绝缘终端可用?
PHOENIX 提供 15 个绝缘系列:环形(RV)、叉形(SV)、刀片(DBV)和销钉(PTV)端子、公断开头和母断开器(MDD / FDD,包括全绝缘类型)、钩式断开器(PBDD)、公头和母头子头(MPD / FRD)、尼龙旗(FLDNY)、弹簧式(MRFNY / FRFNY)以及热缩环和前叉式(RHB / SHB)。
我该如何选择正确的绝缘端子?
匹配三个数值:线材横截面(红色0.5–1.5 mm²,蓝色1.5–2.5 mm²,黑色 2.5–4 mm²,黄色 4–6 mm²),您的螺柱或卡片所需的连接类型,以及螺柱孔、刀片宽度或销钉直径。对于潮湿或高振动环境,选择热缩绝缘型。
环形终端和叉形终端有什么区别?
环形端子完全环绕螺柱,因此在不拆卸螺丝的情况下无法脱落——在存在振动时,这是更安全的选择。叉形端子可滑入松动螺丝下方,无需拆卸即可安装或更换,从而加快组装和维护速度。
绝缘端子上的颜色编码意味着什么?
绝缘端子颜色编码显示线材尺寸范围:红色端子适用于0.5–1.5平方毫米(22–16 AWG)导线,蓝色端子适用于1.5–2.5平方毫米(16–14 AWG),黄色端子适用于4–6 mm²(12–10 AWG),黑色端子适用于2.5–4 mm²导线。该颜色编码系统遵循行业标准,有助于防止安装过程中线与端子的错误匹配。
绝缘端子适合汽车应用吗?
是的,绝缘压接端子广泛应用于汽车照明电路、传感器连接和电力分配的线束。PVC保温层可防止汽车环境中常见的振动、潮湿和温度波动。对于高温应用(发动机舱),热缩绝缘端子可提供高达 125°C 的卓越保护。
PVC 和热缩绝缘端子有什么区别?
PVC绝缘端子采用预成型的乙烯基套管,提供基本的绝缘和应力缓解,适用于大多数室内电气应用。热缩端子采用双层管,加热时会收缩,形成连接处的防水密封。选择热缩端子适用于户外、海洋或恶劣环境,在这些环境中对防潮至关重要。
我可以用绝缘端子搭配绞线和实心线吗?
绝缘压接端子主要为绞铜线设计,绞线在压接时会均匀变形,形成气密连接。虽然技术上它们可以接受实心钢丝,但压接可能没那么可靠,因为实心钢丝压缩效果不如实心钢丝。对于实心导线应用,建议使用专为实心导体设计的线圈或端子。
绝缘端子需要用什么压接工具?
使用带有绝缘端子、尺寸匹配线材的棘轮压接工具。专业级工具配备颜色编码的压接腔(红色、蓝色、黄色),对应端子尺寸,并配有棘轮机构,确保完整的压接循环。避免使用钳子或非棘轮工具,因为它们会造成不均匀的压接,使用过程中可能失效。对于大批量生产,可以考虑气动压接机或电动压接机。
什么是完全绝缘端子和部分绝缘端子?
部分绝缘端子的压接管身外覆PVC材质,但金属连接端暴露,便于目视检查并方便连接端子块或螺柱。全绝缘端子(如我们的FDD Full 系列)覆盖了枪管和连接端,实现了完全的电气隔离。在相邻端子可能接触的狭窄空间内,需要完全绝缘的类型,以防止短路。
你的绝缘端子是否符合RoHS标准?
是的,所有 PHOENIX 绝缘端子均符合 RoHS(危险物质限制)指令,限制铅、汞、镉及其他危险物质的使用。我们的终端采用镀锡T2铜桶和无铅PVC绝缘材料,符合欧盟环保标准,适合出口至国际市场。
绝缘端子的电流额定是多少?
电流额定取决于线径:0.5–1.5 mm²(红色)端子可承受最高 19A,1.5–2.5 mm²(蓝色)最大可承受 27A,2.5–4 mm²(黑色)最大可承受 37A,4–6 mm²(黄色)最大可承受 48A。这些额定值假设在30°C环境温度下连接处正确压接。实际额定值可能因安装条件、线材类型和操作环境而异。对于关键应用,务必查阅制造商的规格说明。
绝缘端子可以在高温环境中使用吗?
标准PVC绝缘端子的连续运行可达105°C。 对于发动机舱或工业供暖设备中较高温度的需求,我们的热缩环(RHB)和叉形(SHB)端子额定温度可达125°C。 对于高于125°C的极端高温应用,建议使用带有独立高温套管或陶瓷绝缘子的非绝缘端子。